CONTACT US
Saleline:0519-83822009
Tel:18706122270
Fax:0519-88739926
E-mail:xrm@czfhd.com
Address:Zhenglu Town, Tianning District,
Changzhou, Jiangsu
Copyright ©2018 Changzhou FHD electronics Co.,Ltd 苏ICP备16043500号-1
Powered by:www.300.cn
PRODUCTS
BM5030STZ-0340-12
1.Technical Parameter
Measuring condition
Part shall be measured under a condition (Temperature: 5~35℃, Humidity: 45%~85%R.H., Atmospheric pressure: 860 ~1060hPa) unless the standard condition (Temperature: 25±3℃, Humidity: 60±10%R.H. Atmospheric pressure: 860 ~1060hPa) is regulated to measure.
1 |
Rated Voltage |
3Vo-p |
2 |
Operating Voltage |
2~5Vo-p |
3 |
Rated Current |
Max.100mA ,at 4000Hz 50% duty Square Wave 3Vo-p |
4 |
Sound Output at 10cm |
Min. 80dB,at 4000Hz 50% duty Square Wave 3Vo-p |
5 |
Coil Resistance |
12±2Ω |
6 |
Resonant Frequency |
4000Hz |
7 |
Operating Temperature |
-20℃~+70℃ |
8 |
Store Temperature |
-40℃~+85℃ |
9 |
Net Weight |
Approx 0.1g |
10 |
RoHS |
Yes |
2.Dimensions Unit: mm
![]() |
![]() |
*Unit: mm; Tolerance: ±0.3mm Except Specified
*Housing Material: Black LCP
*Terminal plate: 3soldering pads, tin Plating Brass
3.Electrical And Acoustical Measuring Condition
Resonant frequency, 1/2 duty cycle. Square wave. Signal amplitude should be large enough tosaturate the transistor. |
![]() |
4.Frequency Response
3Vo-p 50% duty Square wave,10cm
5.Surface mounting condition
5.1Reflow soldering
Recommendable reflow soldering condition is as follows.
Note: (1) In automated mounting of the SMD sound transducers on PCB, any bending, expanding
and pulling forces or shocks against the SMD sound transducers shall be kept minimum
to prevent them from electrical failures and mechanical damages of the devices.
(2) In the reflow soldering, too high soldering temperatures and too large temperature
Gradient such as rapid heating or cooling may cause electrical failures and mechanical
damages of the devices.
5.2 Recommended Soldering pattern
6. Reliability Test After any following tests the part shall meet specifications without any degradation in appearance and performance except SPL. SPL shall not deviate more than -10 dB from the initial value 6.1 Ordinary Temperature Life Test The part shall be subjected to 96 hours at 25±10℃. Input rated voltage Resonant frequency, 1/2 duty Square wave. 6.2 High Temperature Test The part shall be capable of with standing a storage temperature of +85℃ for 96 hours. 6.3 Low Temperature Test The part shall be capable of with standing a storage temperature of -40℃ for 96 hours. 6.4 Humidity Test Temperature:+40℃±3℃ Relative Humidity:90%~95% Duration: 48 hours and expose to room temperature for 6 hours 6.5 Temperature Shock Test Temperature:60℃ /1hour→ 25℃/3hours→-20℃/1hour→ 25℃/3hours (1cycle) Total cycle: 10 cycles 6.6 Drop Test Standard Packaging From 75cm(Drop on hard wood or board of 5cm thick, three sides, six plain.) 6.7 Vibration Test Vibration:1000cycles /min. Amplitude:1.5mm, Duration: 1 hour in each 3 axes 6.8 Reflow Test Use recommendable reflow soldering condition (as shown in 5.1) (1) No abnormality should be found after reflow (2) Good soldering to meet soldering requirements
Note: As this product is not protected from foreign material entering, please make sure that any foreign materials (e.g. magnetic powder, washing solvent, flux, corrosive gas) do not enter this product in your production processes. The functional degradation (e.g. SPL down) may occur if foreign material enter it. |
7.Packing
包装要求 |
编带包装:详见图纸要求 外箱料号:F6-021,外箱尺寸35*18.5*36cm(5盘装) 内箱料号:F6-054,内箱尺寸76*45.5cm 载带料号:F6-S50301,上封带料号:F6-SF133 2500PCS/盘 每个载盘用一个大PE袋装好再放入内盒;PE袋料号:F6-610 |
|
唛头要求 |
内盒: 按客户订单 |
外箱: 按客户订单 |
![]() |
![]() |