Buzzer BE5029-Changzhou FHD electronics Co.,Ltd

Home page

Products

Buzzer BE5029

Parts shall be measured under one condition (temperature: 5~35 ℃, humidity: 45% ~ 85% R.H., atmospheric pressure: 860 ~ 1060hPa), unless standard conditions (temperature: 25±3 ℃, humidity: 60±10%R.H. atmospheric pressure: 860 ~ 1060hPa) are adjusted.

Category： Mechanical buzzer

Online message

Keywords: buzzer | horn | materialized film

Product Description

1. Technical Parameter
Measuring condition
Part shall be measured under a condition (Temperature: 5~35℃, Humidity: 45%~85%R.H., Atmospheric pressure: 860 ~1060hPa) unless the standard condition (Temperature: 25±3℃, Humidity: 60±10%R.H. Atmospheric pressure: 860 ~1060hPa) is regulated to measure.

1	Rated Voltage	120VAC
2	Operating Voltage	90-150 V AC
3	Rated Current	M ax. 70 mA
4	Sound Output at 15cm	Min. 85 dB
5	Coil Resistance	1.5 ±10%K Ω
6	Rated Power	Max. 7.8W
7	Resonant Frequency	50-60 Hz
8	Operating Temperature	-20 ℃ ~ +45 C
9	Store Temperature	- 2 0 ℃ ~ +6 0 ℃
10	Net Weight	Approx 53.0 g
11	RoHS	Yes

2. Dimensions Unit: mm

* Unit: mm; Tolerance: ± 0.5mm Except Specified
* Housing Material: black PBT

3.Reliability Test
After any following tests the part shall meet specifications without any degradation in
appearance and performance except SPL. SPL shall not deviate more than -10 dB
from the initial value
3.1 Ordinary Temperature Life Test
The part shall be subjected to 96 hours 214 at 25±10 ℃ voltage. Resonant frequency, 1/2 duty Square wave.

3.2 High Temperature Test The part shall be capable of with standing a storage temperature of +60 ℃ for 96 hours.

3.3 Low Temperature Test The part shall be capable of with standing a storage temperature of -20 ℃ for 96 hours.

3.4 Humidity Test Temperature:+60 ℃ 2 ℃ Relative Humidity:90% ~ 95% Duration: 96 hours
and exposed to room temperature for 6 hours

3.5 Temperature Shock Test Temperature:-20 ℃/1hour → 20 ℃/1hours →-60 ℃/1hour (1cycle)
Total cycle: 5 cycles

3.6 Drop Test Standard Packaging From 75cm(Drop on hard wood or board of 10cm thick,
three sides, six plain.)

3.7 Vibration Test Vibration:1000cycles /min. Amplitude:1.5mm, Duration: 1 hour in each 3 axes

Note: As this product is not protected from foreign material entering, please make sure that any foreign materials (e.g. magnetic powder, washing solvent, flux, corrosive gas) do not enter this product in your production processes. the functional degradation (e.g. spl down) may occur if foreign material enter it.

4.Packing

1. foam box 30 PCS/box item number: f6-716

packing requirements	2 outer box 120 PCS/box outer box 40.54019.5 4 box item number: F6-022
shipping mark requirements		acceptance requirements

4. 1 Place 30PCS

4.2 in each box according to the arrangement method shown in the figure below. Place two layers of pearl foam strips

with appropriate width between the product and the product. Cover an empty foam box with 4.3. Press it tightly by hand. Put two adhesive tapes

4.4 into the outer box. Put four boxes in each box, add filling, seal and pack