Buzzer BMC9650-Changzhou FHD electronics Co.,Ltd

Home page

Products

Buzzer BMC9650

Parts shall be measured under one condition (temperature: 5~35 ℃, humidity: 45% ~ 85% R.H., atmospheric pressure: 860 ~ 1060hPa), unless standard conditions (temperature: 25±3 ℃, humidity: 60±10%R.H. atmospheric pressure: 860 ~ 1060hPa) are adjusted.

Category： Electromagnetic active buzzer

Online message

Keywords: buzzer | horn | materialized film

Product Description

1. Technical Parameter
Measuring condition

Part shall be measured under a condition (Temperature: 5~35℃, Humidity: 45%~85%R.H.Atmospheric pressure: 860 ~1060hPa) unless the standard condition (Temperature: 25±3℃,Humidity: 60±10%R.H. Atmospheric pressure: 860 ~1060hPa) is regulated to measure.

1	Rated Voltage	5Vo-p
2	Operating Voltage	4-7VDC
3	Rated Current	Max.30mA, at 5VDC
4	Sound Output at 10cm	Min.85dB, at 5VDC
5	Tone	Continuous
6	Resonant Frequency	2700±300Hz
7	Operating Temperature	-20- +70℃
8	Store Temperature	-30 - +80℃
9	Net Weight	Approx 0.7g
10	RoHS	Yes

2. Dimensions Unit: mm

*Unit: mm; Tolerance: ±0.5mm Except Specified
*Housing Material: Black PBT

3. Electrical And Acoustical Measuring Condition

Recommended Test Circuit

Recommended Setting

4.Reliability Test

After any following tests the part shall meet specifications without any degradation in appearance and performance except SPL. SPL shall not deviate more than -10 dB from the initial value
a)Ordinary Temperature Life Test
The part shall be subjected to 96 hours at 25±10℃. Input rated voltage Resonant frequency, 1/2 duty Square wave.
B )High Temperature Test
The part shall be capable of with standing a storage temperature of +80℃ for 96 hours.
c)Low Temperature Test
The part shall be capable of with standing a storage temperature of -30℃ for 96 hours.
d)Humidity Test
Temperature:+40℃±3℃ Relative Humidity:90%~95% Duration: 48 hours and expose to room temperature for 6 hours
e)Temperature Shock Test
Temperature:70℃ /1hour→ 25℃/3hours→-30℃/1hour→ 25℃/3hours (1cycle)
Total cycle: 10 cycles
f)Drop Test
Standard Packaging From 75cm(Drop on hard wood or board of 5cm thick, three sides, six plain.)
g)Vibration Test

Vibration:1000cycles /min. Amplitude:1.5mm, Duration: 1 hour in each 3 axes

Note:

As this product is not protected from foreign material entering, please make sure that any foreign materials (e.g. magnetic powder, washing solvent, flux, corrosive gas) Do not enter this product in your production processes. the functional degradation (e.g. spl down) may occur if foreign material enter it.

5.Packing

packing requirements

1. blister packing, 100 PCS/box blister box material number: f6-409
2. inner box: 2000 PCS/box material number: F6-088-1
3. outer box: 8000 PCS/box material number: F6-088

shipping mark requirements

inner box:

according to customer order

outer box:

is packed according to customer order

1.PVC box, 100 PCS/box

2.20 boxes/stack of 2000PCS/stack is padded with a cardboard under it, an empty PVC box is placed on it and then a cardboard is placed, the adhesive tape is drilled as shown in the figure, and a plastic bag is set, after putting desiccant, seal the bag

3. put the sealed bag into the inner box, four boxes/box
outer box 8000 PCS/box four boxes/box